| |
Product SKUs |
| MBD-X8DTN+-F-O | - X8DTN+-F
- (Standard Retail Pack)
|
| MBD-X8DTN+-F-B | |
| |
Physical Stats |
| Form Factor | Enhanced Extended ATX |
| Dimensions | 13.68" x 13" (34.7cm x 33cm) |
| |
Processor/Cache |
| CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel 64-Bit Xeon processor(s) of the same type below:
- Intel Xeonprocessor 5600 Series (Westmere)
- Intel Xeonprocessor 5500 Series (Nehalem-EP)
|
| QPI | Up to 6.4 GT/s |
| |
System Memory |
| Memory Capacity | - 18x 240-pin DIMM sockets
- Supports up to 288 GB 1333 / 1066 / 800 MHz DDR3 ECC registered memory
- Supports up to 48 GB 1333 / 1066 / 800 MHz DDR3 ECC / Non ECC unbuffered memory
- Memory Mirroring supported
|
| Memory Type | 1333 / 1066 / 800MHz ECC registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes | - 1GB, 2GB, 4GB
- , 8 GB
- , 16 GB
|
| Memory Voltage | 1.5 V / 1.35 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel x4 and x8 Single Device Data Correction (SDDC)
|
| Note: | This board does not support LRDIMM memory. |
| |
On-Board Devices |
| Chipset | - Intel 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
|
| SATA | - Intel ICH10R SATA 3.0 Gb/s controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
|
| IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM over LAN support
- Winbond® WPCM450 BMC
|
| Network Controllers | - Intel 82576 Dual-Port Gigabit Ethernet controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- Intel I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics | Matrox G200eW |
| Super I/O | Winbond 83657HG chip |
| |
Input / Output |
| Serial ATA | - 6 Serial ATA ports
- 6 SATA hard drives supported
|
| LAN | - 2 RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB | - 4 USB rear ports
- 1 TypeA USB connector
- 3 USB internal headers( 5 ports)
- 10 total USB ports, 2.0 Compliant
|
| VGA | 1 VGA Port |
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Port / Header | - 1x Fast UART 16550 serial port
- 1 Fast UART 16550 serial header (opt)
|
| |
Chassis ( Optimized for X8DTN+-F
) |
| 2U Chassis | - CSE-213A-R900LPB
- CSE-216A-R900LPB
- CSE-216E1-R900LPB
- CSE-216E2-R900LPB
- CSE-823MTQ-R700LPB
- CSE-825MTQ-R700LPB
- CSE-825TQ-563LPB
- CSE-826A-R1200LPB
- CSE-826E1-R800LPB
- CSE-826E2-R800LP
- CSE-826TQ-R800LPB
|
| 3U Chassis | - CSE-836E1-R800B
- CSE-836E2-R800B
- CSE-836TQ-R800B
- CSE-936E1-R900
- CSE-936E16-R1200B
- CSE-936E26-R1200B
|
| Tower / 4 U Rackmount | - CSE-846E1-R900B
- CSE-846E16-R1200B
- CSE-846E2-R900
- CSE-846E26-R1200B
- CSE-846TQ-R900B
|
| Important Chassis Notes | To support the new generation Intel® Xeon® processor-based motherboards, a Revision K chassis is recommended for most models. Please talk to your sales representative or follow the link for details. |
| |
Expansion Slots |
| PCI-Express | - 2 (x8) PCI-E slots (in x16 slots)
- 2 (x4) PCI-E slots (in x8 slots)
- 1x (x4) PCI-E slot (in x8 slot)
|
| UIO | 1x UIO slot (PCI-E 2.0 x8 slot) |
| |
System BIOS |
| BIOS Type | 32Mb SPI Flash EEPROM with AMI BIOS |
| BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| |
Management |
| Software | - IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
|
| Power Configurations | ACPI / ACPM Power Management |
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +3.3V, +5V, +12V, +5V Standby, VBAT, HT Voltages.
- 6-Phase-switching voltage regulator
|
| FAN | - Total of eight fan headers supporting up to 8 fans
- Eight 4-pin fan headers
- 8x fans with tachometer status monitoring
- Supports 3-pin fans (w/o speed control)
- Low noise fan speed control (4-pin fan only)
|
| Temperature | - Monitoring for CPU and chassis environment
- Thermal Control for 8x fan connectors
- PECI
|
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant 6/6, Pb Free |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
| |
OS compatibility |
| Please see our OS Compatibility Chart |
0 Articoli
