| |
Product SKUs |
| MBD-X9DBL-i -O | X9DBL-i (Standard Retail Pack) |
| MBD-X9DBL-i -B | X9DBL-i (Bulk Pack) |
| |
Physical Stats |
| Dimensions | 12" x 10" (30.48cm x 25.4cm) |
| |
Processor/Cache |
| CPU | - Intel® Xeon® processor E5-2400 and E5-2400 v2 (up to 95W TDP **)
- Dual Socket B2 (LGA 1356)
|
| Cache | Up to 25 MB |
| System Bus | QPI up to 8 GT/s |
| ** Motherboard supports this maximum TDP. Please verify your system can thermally support |
| |
System Memory |
| Memory Capacity | - 6x 240-pin DDR3 DIMM sockets
- Up to 384GB DDR3 ECC LRDIMM
- Up to 192GB DDR3 ECC Registered memory (RDIMM)
- Up to 48GB DDR3 ECC/non-ECC Un-Buffered memory (UDIMM)
|
| Memory Type | - 1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Supports ECC and non-ECC UDIMMs
- * Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed.
|
| DIMM Sizes | 32 GB, 16 GB, 8 GB, 4 GB, 2 GB, 1 GB |
| Memory Voltage | 1.5 V, 1.35 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| |
On-Board Devices |
| Chipset | Intel C602 chipset |
| SATA | - SATA 2.0 3Gb/s with RAID 0, 1, 5, 10
- SATA 3.0 6Gb/s with RAID 0, 1, 5, 10
|
| AHCI SATA | - SATA 2.0 3 Gb/s with RAID 0, 1, 5, 10
- SATA 3.0 6 Gb/s with RAID 0, 1, 5, 10
|
| SCU SATA | SATA 2.0 3 Gb/s with RAID 0, 1, 5, 10 |
| SAS | - SAS from C606
- RAID 0, 1, 10 support
|
| IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM over LAN support
- Nuvoton WPCM450 BMC
|
| Network Controllers | - Intel 82574L Gigabit Ethernet
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
|
| Video | G200 (Nuvoton WPCM150G) |
| Super I/O | Nuvoton W83527HG |
| |
Input / Output |
| SATA | - 2x SATA 3.0 ports (6Gb/s)
- 8x SATA 2.0 ports (3Gb/s)
|
| AHCI SATA | - 2x SATA 3.0 ports (6 Gb/s)
- 4x SATA 2.0 ports (3 Gb/s)
|
| SCU SATA | 4x SATA 2.0 ports (3 Gb/s) |
| SAS | 8x SAS/SATA2 ports |
| LAN | 2x RJ45 Gigabit Ethernet LAN ports |
| USB | 7x USB 2.0 ports total(2x rear + 4x via header + 1x Type A) |
| Video | 1x VGA port |
| Serial Port / Header | 2x Fast UART 16550 ports / 1 rear and 1 header |
| DOM | 1x DOM (Disk on Module) power connector |
| |
Chassis (Optimized for X9DBL-i ) |
| 1U Chassis | - CSE-113MTQ-600CB
- CSE-813MTQ-350C
- CSE-813MTQ-441CB
- CSE-813MTQ-R400CB
|
| 2U Chassis | CSE-823TQ-653B |
| 3U Chassis | CSE-833T-653B |
| Tower / 4 U Rackmount | - CSE-842TQ-665B
- CSE-842TQ-865B
|
| Important Chassis Notes | To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis are recommended. |
| |
Expansion Slots |
| PCI-Express | - 1x PCI-E 3.0 x16
- 3x PCI-E 3.0 x8
- 1x PCI-E 3.0 x4 (in x8)
- 1x PCI-32
- (Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.)
|
| |
System BIOS |
| BIOS Type | 64Mb SPI Flash EEPROM with AMI BIOS |
| BIOS Features | - Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI 2.3.1
|
| |
Management |
| Software | - SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations | - ACPI / APM Power Management
- Power-on mode for AC power recovery
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory Voltages.
- 5+1 Phase-switching voltage regulator
|
| FAN | - Six 4-pin fan headers with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 6x Fan Connectors
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED | - CPU / System Overheat LED
- Supsend-State Indicator LED
- UID/Remote UID
|
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
- RoHS, Halogen Free
- Dual Cooling Zones
|
| |
Operating Environment |
| Operating Temperature Range | 10°C - 35°C (50°F - 95°F) |
| Non-Operating Temperature Range | -40°C - 70°C (-40°F - 158°F) |
| Operating Relative Humidity Range | 8% - 90% (non-condensing) |
| Non-Operating Relative Humidity Range | 5% - 95% (non-condensing) |
0 Artikel
