| |
Product SKUs |
| MBD-X9DRH-7TF -O | X9DRH-7TF (Standard Retail Pack) |
| MBD-X9DRH-7TF -B | X9DRH-7TF (Bulk Pack) |
| |
Physical Stats |
| Form Factor | Extended ATX |
| Dimensions | 12.1" x 13" (30.7cm x 33.2cm) |
| |
Processor/Cache |
| CPU | - Dual Socket R (LGA 2011)
- Intel® Xeon® processor E5-2600 and E5-2600 v2 family?
- (up to 135W TDP **)
|
| Note | ** Motherboard supports this maximum TDP. Please verify your system can thermally support. |
| Cache | Up to 30 MB |
| System Bus | QPI up to 8 GT/s |
| |
System Memory |
| Memory Capacity | - 16x 240-pin DDR3 DIMM sockets
- Up to 1 TB DDR3 ECC LRDIMM
- Up to 512GB DDR3 ECC RDIMM
- Up to 128GB DDR3 ECC/non-ECC UDIMM
|
| Memory Type | - 1866/1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Support ECC and non-ECC UDIMMs* Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed.
|
| DIMM Sizes | 32 GB, 16 GB, 8 GB, 4 GB, 2 GB, 1 GB, 64 GB LRDIMM |
| Memory Voltage | 1.5 V, 1.35 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| |
On-Board Devices |
| Chipset | Intel C602 chipset |
| AHCI SATA | - SATA 2.0 3Gb/s with RAID 0, 1, 5, 10
- SATA 3.0 6Gb/s with RAID 0, 1
|
| SCU SATA | SATA 2.0 3Gb/s with RAID 0, 1, 10 |
| SAS | - SAS-2 from LSI 2208 (1 GB cache)
- HW RAID 0, 1, 5, 6, 10, 50, 60 support
- Supports up to 16 devices as default, more HDD devices support is also available as an option ** For special sku, please contact your Supermicro Sales.
|
| IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM over LAN support
- Nuvoton WPCM450 BMC
|
| Network Controllers | - Intel X540 Dual port 10GBase-T
- Virtual Machine Device Queues reduce I/O overhead
- Supports 10GBase-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Video | Matrox G200eW |
| |
Input / Output |
| AHCI SATA | - 2 SATA 3.0 ports (6Gb/s)
- 4 SATA 2.0 ports (3Gb/s)
|
| SCU SATA | 4 SATA 2.0 ports (3Gb/s) |
| SAS | 8 SAS2 ports (6Gb/s) |
| LAN | - 2x RJ45 10GBase-T ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB | 7 USB 2.0 ports total(4 rear + 2 via header + 1 Type A) |
| Video | 1x VGA port |
| Serial Port / Header | 2 Fast UART 16550 serial COM port(1 rear & 1 header) |
| DOM | 1x DOM (Disk on Module) power connector |
| TPM | 1 TPM 1.2 20-pin Header |
| |
Chassis (Optimized for X9DRH-7TF ) |
| 2U Chassis | - CSE-825TQ-R740LPB
- CSE-826BA-R1K28LPB
- CSE-826BA-R920LPB
- CSE-826BE16-R1K28LPB
- CSE-826BE16-R920LPB
- CSE-826BE26-R1K28LPB
- CSE-826BE26-R920LPB
|
| 3U Chassis | - CSE-835TQ-R920B
- CSE-836BA-R1K28B
- CSE-836BE16-R1K28B
- CSE-836BE26-R1K28B
|
| Tower / 4 U Rackmount | - CSE-743TQ-1200B
- CSE-743TQ-865B
- CSE-743TQ-903B
- CSE-745TQ-R1200B
- CSE-745TQ-R800B
- CSE-745TQ-R920B
- CSE-846BA-R1K28B
- CSE-846BE16-R1K28B
- CSE-846BE26-R1K28B
- CSE-847A-R1400B
- CSE-847A-R1K28LPB
- CSE-847E16-R1400B
- CSE-847E16-R1K28LPB
- CSE-847E26-R1400B
- CSE-847E26-R1K28LPB
|
| Important Chassis Notes | To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis are recommended. |
| |
SuperServer(s) with X9DRH-7TF |
| Model(s) | - SSG-2027R-AR24
- SSG-6027R-E1R12T
- SYS-6027R-72RFT
- SYS-7047R-72RFT
|
| |
Expansion Slots |
| PCI-Express | - 1x PCI-E 3.0 x16
- 6x PCI-E 3.0 x8
- (Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.)
|
| |
System BIOS |
| BIOS Type | 128 Mb SPI Flash EEPROM with AMI BIOS |
| BIOS Features | - Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI 2.3.1
|
| |
Management |
| Software | - SuperDoctor® III
- Watch Dog
- NMI
- IPMI 1.5 / 2.0
|
| Power Configurations | - ACPI / APM Power Management
- Power-on mode for AC power recovery
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory Voltages.
- 5+1 Phase-switching voltage regulator
|
| FAN | - 8x 4-pin fan headers (up to 8 fans)
- 8x fans with tachometer monitoring
- Status monitor for speed control
- Pulse Width Modulated (PWM) fan connectors
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED | CPU / System Overheat LED |
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
- RoHS, Halogen Free
- Dual Cooling Zones
|
| |
Operating Environment |
| Operating Temperature Range | 10°C - 35°C (50°F - 95°F) |
| Non-Operating Temperature Range | -40°C - 70°C (-40°F - 158°F) |
| Operating Relative Humidity Range | 8% - 90% (non-condensing) |
| Non-Operating Relative Humidity Range | 5% - 95% (non-condensing) |
0 Artikel
