|
Product SKUs |
MBD-X9DRi-LN4F+ -B | X9DRi-LN4F+ (Bulk Pack) |
|
Physical Stats |
Form Factor | Enhanced Extended ATX |
Dimensions | 13.68" x 13" (34.7cm x 33cm) |
|
Processor/Cache |
CPU | - Dual Socket R (LGA 2011)
- Intel® Xeon® processor E5-2600 and E5-2600 v2 family?
- (up to 135W TDP **)
|
Note | ** Motherboard supports this maximum TDP. Please verify your system can thermally support. |
Cache | Up to 30 MB |
System Bus | QPI up to 8 GT/s |
|
System Memory |
Memory Capacity | - 24x 240-pin DDR3 DIMM sockets
- Up to 1.5 TB DDR3 ECC LRDIMM
- Up to 768 GB DDR3 ECC RDIMM
- Up to 128GB DDR3 ECC/non-ECC UDIMM
|
Memory Type | - 1866/1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Support ECC and non-ECC UDIMMs* Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed.
|
DIMM Sizes | 32 GB, 16 GB, 8 GB, 4 GB, 2 GB, 1 GB, 64 GB LRDIMM |
Memory Voltage | 1.5 V, 1.35 V |
Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
|
On-Board Devices |
Chipset | Intel C602 chipset |
AHCI SATA | - SATA 2.0 3 Gb/s with RAID 0, 1, 5, 10
- SATA 3.0 6 Gb/s with RAID 0, 1, 5, 10
|
SCU SATA | SATA 2.0 3 Gb/s with RAID 0, 1, 5, 10 |
IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM over LAN support
- Nuvoton WPCM450 BMC
|
Network Controllers | - Intel® i350 Gigabit Ethernet (x4 ports)
- Virtual Machine Device Queues reduce I/O overhead
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
Video | Matrox G200eW |
|
Input / Output |
AHCI SATA | - 2x SATA 3.0 ports (6 Gb/s)
- 4x SATA 2.0 ports (3 Gb/s)
|
SCU SATA | 4x SATA 2.0 ports (3 Gb/s) |
LAN | - 4 RJ45 Gigabit Ethernet LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
USB | 9 USB 2.0 ports total(4 rear + 4 via header + 1 Type A) |
Video | 1x VGA port |
Serial Port / Header | 2 Fast UART 16550 ports: 1 rear and 1 header |
DOM | 1x DOM (Disk on Module) power connector |
TPM | 1 TPM 1.2 20-pin Header |
|
Chassis (Optimized for X9DRi-LN4F+ ) |
2U Chassis | - CSE-825TQ-R740LPB
- CSE-826E16-R920LP
|
3U Chassis | - CSE-835TQ-R920B
- CSE-836BA-R920B
|
Tower / 4 U Rackmount | - CSE-745TQ-R920B
- CSE-846BE16-R920B
- CSE-847E16-R1K28LPB
|
Important Chassis Notes | - To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis are recommended.
- Please use optional I/O shield MCP-260-00041-0N in Supermicro 1U chassis
|
|
SuperServer(s) with X9DRi-LN4F+ |
Model(s) | - SSG-2027R-E1CR24N
- SSG-2027R-E1R24N
- SSG-6027R-E1CR12N
- SSG-6027R-E1CR36N
- SSG-6027R-E1R12N
- SSG-6037R-E1R16N
- SSG-6047R-E1CR36N
- SSG-6047R-E1R24N
- SSG-6047R-E1R36N
|
|
Expansion Slots |
PCI-Express | - 4 (x16) PCI-E 3.0 slots
- 1x (x8) PCI-E 3.0 slot
- 1 (x4) PCI-E 3.0 (in x8) slot
- (Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.)
|
|
System BIOS |
BIOS Type | 128 Mb SPI Flash EEPROM with AMI BIOS |
BIOS Features | - Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI 2.3.1
|
|
Management |
Software | - SuperDoctor® III
- Watch Dog
- NMI
- IPMI 1.5 / 2.0
|
Power Configurations | - ACPI / APM Power Management
- Power-on mode for AC power recovery
|
|
PC Health Monitoring |
Voltage | - Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory Voltages.
- 6+1 Phase-switching voltage regulator
|
FAN | - 8x 4-pin fan headers (up to 8 fans)
- 8x fans with tachometer monitoring
- Status monitor for speed control
- Pulse Width Modulated (PWM) fan connectors
|
Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- Thermal Monitor 2 (TM2) support
- PECI
|
LED | - CPU / System Overheat LED
- Supsend-State Indicator LED
- UID/Remote UID
|
Other Features | - Chassis intrusion detection
- Chassis intrusion header
- RoHS, Halogen Free
|
|
Operating Environment |
Operating Temperature Range | 10°C - 35°C (50°F - 95°F) |
Non-Operating Temperature Range | -40°C - 70°C (-40°F - 158°F) |
Operating Relative Humidity Range | 8% - 90% (non-condensing) |
Non-Operating Relative Humidity Range | 5% - 95% (non-condensing) |